Dynamix DW 4 FXO Podręcznik Użytkownika

User Guide VoIP GatewayDYNAMIX 2504 (FXS-04)

10 set the dedicate FXS SIP proxy server. (See Figure 1-6-6 SIP Proxy) Figure 1-6-6 SIP Proxy Step 7: Setup each FXS line’s parameters by clicking

11 Step 9: After soft-reset or reboot. >Click Status > SIP Trunk Status to check whether registered or not. (See Figure 1-6-9 SIP Trunk Stat

12 CH2 Device Settings From this setting category, all devices related parameters can be found here. 2-1 Network Configuration > Network Figure

13 LAN Setting:  Management mode: This LAN port is used for management purpose, not used for register or routing.  NAT mode: DHCP function on th

14 2-2 Device Time Setting Device Setting > Time Figure 2-2 Time setting Parameter Description:  Now: Current Time (display only)  NTP Tim

15 2-3 Device Advance Setting > Advance Figure 2-3 Advance setting Parameter Description:  HTTP Service: The Administrator Web service port

16 2-4 User Login Setting Three level of users can be used, administrator, supervisor, user. Each level of users will have different predefined acces

17 2-5 Debug Settings generates the debug information based on debug level and modules. Since the generating debug will consume system resource, it i

18 2-6 Event Notice 1. Register Failure or re-registered 2. FXO is plug or unplug 3. Ethernet reconnected 4. System started Figure 2-6 E

19 2-7 Auto Provisioning >Provisioning Figure 2-7-1 Provisioning Select 9510: Figure 2-7-2 Provisioning type of 9510 Parameter Descripti

2 Contents CH1 Introduction ... 4 1-1 Physical Interface ...

20 broadcasting port (default is 61005). report its summary status to WellEMS 9510 in seconds.  EMS IP address: The WellEMS 9510 server IP address

21 2-8 SNMP Figure 2-8 SNMP SNMP Agent:  SNMP Agent: Enable SNMP or not.  Read Only Community Name: The community name to read through SNMP pr

22 CH3 NAT Setting are the settings for NAT related service. 3-1 DHCP Ser. (DHCP server) Figure 3-1 DHCP server  DHCP Server: Enable DHCP server

23 3-2 UPNP (universal plug and play server) Figure 3-2 UPnP  UPNP IGD: Enable UPNP server or not. 3-3 Bandwidth (Bandwidth Control) By using ba

24 the required bandwidth  percentage : total bandwidth  priority 1: highest priority percentage  priority 2: Normal priority percentage 

25 IP Target Figure 3-3-4 IP Target 1 Figure 3-3-5 IP Target 2  Priority: Priority value for the target  Type: The target type is set to IP

26  Type: The target type is set to port number  Configure Type: unique port number or a range of port number  Unique:  Port: the port number

27 3-4 URL Filter Figure 3-4 URL Filter  URL Filter: the specified url will be blocked 3-5 IP Filter Figure 3-5 IP Filter  IP Filter: The s

28 3-6 MAC Filter Figure 3-6 MAC Filter  MAC Filter: The MAC address to be blocked 3-7 APP Filter Figure 3-7 App Filter  APP Filter: appli

29 3-8 Port Filter Figure 3-8 Port Filter  Port Filter: enable port Filter or not.  Port Range: Starting and stopping port to be forward. If yo

3 5-1 SIP ... 35 5-2 Audio ...

30 VOIP Parameters Setting SIP Parameters: CH4 VOIP Setting 4-1 SIP Figure 4-1 SIP setting Parameter Description:  Session Timer: Enable sess

31 4-2 Audio Figure 4-2 Audio setting  Codec 1~5: The preferred codec priority  G.711u Payload Size: G.711 u-Law payload size  G.711a Payloa

32  Silence Suppression: Enable: Start the voice activity (silence) detection when detect silence for 60 seconds, it will hang up the call (For FX

33 4-3 Tone The setting page is used to setup the tone to be generated or detected. The detected tone is the Disconnect 1 & 2 (for FXO use) and t

34 4-4 NAT Traversal Figure 4-4 NAT Traversal  NAT Traversal:  Disable: Disable NAT traversal features  STUN (Type 1,2): Enable STUN for N

35 CH5 VOIP Advance 5-1 SIP Figure 5-1 SIP Parameter Description:  SIP Hold Type: SIP on hold message sending method. - Send Only: Set the SDP

36  SIP T2 (msec): Determines the maximum retransmission interval as defined in RFC3261. For example, when an unreliable transport protocol is used

37 will think the request is failed. The default is 5 seconds.  MWI Subscript Expires (sec): You can Enable or Disable the MWI subscribe. The defau

38  DTMF Relay Volume: The DTMF relay volume  T.38 Fax Volume: The T.38 fax relay volume  T.38 Redundant Depth: The T.38 redundant packet depth

39 5-3 Ring The ring cadence, voltage and frequency for the phone Figure 5-3 Ring setting  Frequency (10~70HZ): Specify the ringing frequency val

4 CH1 Introduction FXS-04 Telephony Gateway includes 1-WAN/1-LAN (management port) 10/100 base-T network environment. Field-proven quality of Voic

40 CH6 Dialing Plan 6-1 General Figure 6-1 General setting  First Digit Time Out: Specify the duration of dial waiting when the receiver is off h

41 6-2 Dialing Rule Figure 6-2 Dialing Rule setting Dialing rule is used to speed up the dialing procedure. Some user don’t like to use the end of

42 6-3 Digit Manipulation The Digit Manipulation will be processed based on prefix and DM group after the DNIS is determined. Figure 6-3 Digit

43 6-4 Phone Book Phone Book is used for peer to peer call. Figure 6-4 Phone Book setting  Name: This field supports called number only. If you e

44 CH7 FXS Setting The FXS line setting includes each line number and SIP proxy settings. Figure 7-0 FXS setting  Line ID: FXS line (TEL1 to TEL

45 7-1 FXS line Figure 7-1 FXS setting  User ID: FXS Line number (TEL1 to TEL4)  User Type: The line type, FXO or FXS  Line State: Set to act

46 billing signal or not. When a FXS calls to VOIP and answered by the as a billing stop signal.  Current Drop generation: Enable current drop (0

47 7-2 SIP Proxy The SIP proxy server defined here is dedicated used for FXS lines. Figure 7-2 FXS setting  Domain: The SIP domain for registe

48 7-3 Caller ID The call ID stand for the phone Figure 7-3 Caller ID setting  Caller ID Mode: Caller ID mode to be u sed for phone (FSK Bellco

49 7-4 Others Flash time and current drop generation time Figure 7-4 Others setting  Min flash time(80~800msec): Specify the value of the flash (

5 TCP/UDP (RFC 793/768) RTP/RTCP (RFC 1889/1890) IPV4 ICMP (RFC 792)/IPV6 ICMP (RFC 4443) TFTP Client VOIP VLAN Support (802.1q/802.1p) HTTP/HTTPS Se

50 CH8 SIP Trunk The administrator needs to set the SIP trunk for VOIP outgoing call and incoming call. There are up to 4 SIP trunk can be used for w

51 8-1 Create SIP Trunk Figure 8-1 SI P Tr unk page  Trunk ID: SIP trunk ID 1-4  Register Type: Whether this account need register or not REGIS

52 part. The SIP FROM header’s URL will be the SIP_User_ID@Domain or SIP_User_ID@SIP_Proxy_Server.  Keep Alive: Enable or Disable it.  Keep Ali

53 CH9 Route Plan incoming call type/target, length and prefix to determinate the outgoing call process. For VOIP incoming call, it can send to FXS i

54 9-1 Create Route Plan Click Route Plan and Click new to create a new routing policy. Figure 9-1 Route Plan setting  Incoming Call Type: Incom

55  Cyclic Ring: The call will be hunted based on the cyclic basis. This is the recommended method.  Routing List:  The routing target list wil

56 CH10 Status Figure 10-0 Status page 10-1 Device States See the figure 10-0 Status page  Model: The model number  Network Type: The Net

57 10-2 Line States This page shows the each line’s current status. Figure 10-2 Line Status  Line: L1 to L4  Account: display each line number

58 10-3 SIP Trunk States Figure 10-3 SIP Trunk Status  Account: SIP trunk account  Registered: The SIP trunk register status  Concurrent Call

59 CH11 Maintenance firmware or reset. Figure 11-0 Maintenance  Backup: Backup the system settings for restoring purpose  Reset to Default: R

6 Status When system is startup successfully, the LED will light up green. Proxy When the gateway is registered successfully to a Proxy, this will li

60 Appendix A--- System Recovery you will not encounter the system failed to boot issue. Normally, the user should able to use Web page to login and

61 - download the firmware into tftp data directory 6. In the telnet terminal, do the following command - 1. __dmctw - 2. cd /config_fs - 3.

62 - 4. copy firmware successfully - 5. reboot 7. Check whether the system was recovered or not

63 Appendix B --- HTTP auto provisioning follows: Step 1: build mac list for mass configuration file generation Please open the “wg2504 MAC

64 Step 4: Generate the individual configuration file. Double click the “wtgencfg.exe”, it will generate the configuration file for each MAC list in

65 in peer to peer mode with hotline by port to port application. Purpose This paper is going to describe how to configure FXO to FXS in peer to p

66 IP address : 192.168.23.23 SIP Line number : 1001, 1002, 1003 and 1004 FXO Telephone Number : default is Blank PABX Extension number 201, 202, 20

67 FXS port #1 point to remote FXO port #1 directly. Continue to configure FXS port number 2 to 4 as following example at Modify Line Setting web pag

68 FXS port 2 number 502 hotline to FXO SIP Trunk 2 which number is 1002, FXS port 3 number 503 hotline to FXO SIP Trunk 3 which number is 1003, FXS

69 Figure 6. webpage Dialing Plan Phone Book. See Figure 7. 8080. The FXS gateway’s phone Book format is as follows. FXO_line_number@FXO_ip_addre

7 for management purpose. WAN 10/100 Base-T RJ-45 socket for WAN port, connects to wide area network. DC 12V The power socket, input AC 100V~240V; ou

70 following picture. See Figure 8. For example: Set static IP address 192.168.23.23 on Device Setting Figure 8. Step 2: Go to VOIP Setting  SIP

71 FXO SIP port 2 number 1002 hotline to remote FXS port 2 number 502 directly. FXO SIP port 3 number 1003 hotline to remote FXS port 3 number 503 di

72 User ID : 1003 User password: 1003 Display Name: 1003 Enter SIP Trunk #4 information as follows. TEL No : 1004 User ID : 1004 User password: 1004

73 Step 5: Set Route Plan to each FXO line. Disable the “VOIP Default Route” first. Figure 12. Set the Incoming Call Type to VOIP; Matched Prefi

74 Figure 13. b. Line #2 of FXO Gateway setting, see Figure 14. An FXS port 2 incoming call routes to FXO port 2 configuration example. Incoming C

75 Figure 15. d. Line #4 of FXO Gateway setting, see Figure 16. An FXS port 4 incoming call routes to FXO port 4 configuration example. Incoming C

76 4. Configure incoming Ring Cadence to FXO Gateway Advance  Ring to configure proper Ring Cadence ( Ring ON time and Ring OFF time ) according

77 See Figure 18. Step 2: Go to FXO Gateway webpage configuration at SIP Trunk  Modify SIP Trunk to enable Outgoing Caller ID with both Display Na

78 See figure 19. FXO Gateway Caller ID Mode. Figure 20. FXO Telephone Number. Figure 21. Go to FXS Setting  FXS Line  Caller ID Mode to select

79 Step 4: Select FXS gateway’s Caller ID Mode. See Figure 22 and 23. FXS Gateway Caller ID generation is able to configure which Caller ID mode in o

8 figure 1-6-2 Network configure-1) Figure 1-6-2 Network configure-1 Change Default IP Network: Step 3: After successfully logon to the system

80 Figure 23. Three options of Caller ID Mode.

81 6. Release FXO Line from PSTN or PABX extension after call was dropped. FXO analog interface detect disconnect tone which was sent from PABX e

82 Figure 25. Loop Current Drop to release FXO port Figure 26. Loop Current Drop detection Time.

83 7. FLASH command generation and detection on FXO and FXS gateway. FLASH feature is widely used for PABX extension to implement PABX’s advanced

84 Figure 28. Setup FXO Flash time generation.

9 Change Default Time setting: Step 4: When re-logon to the new IP address, the next is to setup the system time zone. Click Device Setting > Tim